Iei-integration PCIE-Q870-i2 Bedienungsanleitung

PCIE-Q870-i2 PICMG 1.3 CPU Card Page iUser Manual MODEL: PCIE-Q870-i2 Full-Size PICMG 1.3 CPU Card Supports LGA1150 Intel®Core™ i7/i5/i3, Pentium®

PCIE-Q870-i2 PICMG 1.3 CPU CardPage x List of Figures Figure 1-1: PCIE-Q870-i2...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 835.3.6 Intel(R) Rapid Start Technology Use the Intel(R) Rapid Start Technology (BIOS Menu 8) menu to configure

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 84 5.3.7 AMT Configuration The AMT Configuration menu (BIOS Menu 9) allows the Intel® AMT options to be configu

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 855.3.8 USB Configuration Use the USB Configuration menu (BIOS Menu 10) to read USB configuration information a

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 86 Î Disabled Legacy USB support disabled Î Auto Legacy USB support disabled if no USB devices are connected 5

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 875.3.9.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 12) to configure the

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 88 Î IO=3F8h; IRQ=3, 4 Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4 Î IO=2C0h; IRQ

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 89Î Device Mode [RS422/485] The serial port 2 is set to RS-422/485 mode. 5.3.9.1.3 Serial Port 3 Configuration

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 90 Î Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interr

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 91Î IO=2D0h; IRQ=10 Serial Port I/O port address is 2D0h and the interrupt address is IRQ10 Î IO=2C0h; IRQ=10,

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 92 Î Disabled Disable the parallel port Î Enabled DEFAULT Enable the parallel port Î Change Settings [Auto] Us

PCIE-Q870-i2 PICMG 1.3 CPU Card Page xiFigure 3-27: USB 3.0 Connector Location ...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 935.3.10 F81866 H/W Monitor The F81866 H/W Monitor menu (BIOS Menu 14) contains the fan configuration submenu,

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 94 o VSB5V o VCC3V o VSB3V o VBAT 5.3.10.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 95Î Fan start/off temperature Use the + or – key to change the Fan start/off temperature value. Enter a deci

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 96 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced COM1 Console Redi

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 97Î VT-UTF8 The target terminal type is VT-UTF8 Î ANSI DEFAULT The target terminal type is ANSI Î Bits per se

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 98 Î Stop Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a se

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 995.4 Chipset Use the Chipset menu (BIOS Menu 18) to access the PCH IO and System Agent (SA) configuration menu

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 100 5.4.1 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 19) to configure the PCH parameters.

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 101Î PCIEX16 Power [1 x16 PCIE] Use the PCIEX16 Power BIOS option to configure the PCIe x16 channel mode on th

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 102 5.4.1.1 PCI Express Configuration Use the PCI Express Configuration menu (BIOS Menu 20) to configure the PCI

PCIE-Q870-i2 PICMG 1.3 CPU CardPage xii Figure 6-9: Graphics Driver License Agreement...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 103Î PCIe Speed [Gen1] Use this option to select the support type of the PCI Express ports. The following opti

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 104 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security S

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 105Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset VT-d [Disabled]

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 106 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Graphics Configuration

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 107Î DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size us

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 108 5.4.2.2 NB PCIe Configuration Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 109Î Detect Non-Compliance Device [Enabled] Use the Detect Non-Compliance Device option to enable or disable d

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 110 5.5 Boot Use the Boot menu (BIOS Menu 28) to configure system boot options. Aptio Setup Utility – Copyright

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 111Î Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Î

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 112 Î Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy n

PCIE-Q870-i2 PICMG 1.3 CPU Card Page xiiiFigure B-14: Select a Local Source Drive ...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 113Î User Password Use the User Password to set or change a user password. 5.7 Save & Exit Use the Safe

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 114 Î Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaul

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 115 6 Software Drivers Chapter 6

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 116 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the produc

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 117 Figure 6-1: Introduction Screen Step 3: Click PCIE-Q870. Step 4: A new screen with a list of available dr

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 118 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access th

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 119 Figure 6-4: Chipset Driver License Agreement Step 9: The Read Me file in Figure 6-5 appears. Step 10: Clic

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 120 Figure 6-6: Chipset Driver Setup Operations Step 13: The Finish screen in Figure 6-7 appears. Step 14: Sele

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 1216.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access th

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 122 Figure 6-9: Graphics Driver License Agreement Step 8: The Read Me file in Figure 6-10 appears. Click Next

PCIE-Q870-i2 PICMG 1.3 CPU CardPage xiv List of Tables Table 1-1: PCIE-Q870-i2 Specifications...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 123 Figure 6-11: Graphics Driver Setup Operations Step 11: The Finish screen in Figure 6-12 appears. Step 12: S

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 124 6.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Access the driver l

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 125 Figure 6-14: LAN Driver Welcome Screen Step 8: Click Next to continue. Step 9: The License Agreement in F

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 126 Step 12: The Setup Options screen in Figure 6-16 appears. Step 13: Select program features to install. Step

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 127 Figure 6-17: LAN Driver Installation Step 17: The program begins to install. Step 18: When the driver insta

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 128 6.6 USB 3.0 Driver Installation WARNING: Do not run this driver’s installer (Setup.exe) from a USB storage

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 129Step 7: Read the License Agreement. Step 8: Click Yes to continue. Figure 6-20: USB 3.0 Driver License A

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 130 Step 11: Setup Operations are performed as shown in Figure 6-22. Step 12: Once the Setup Operations are comp

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 131 Figure 6-23: USB 3.0 Driver Installation Finish Screen 6.7 Audio Driver Installation To install the audio d

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 132 Figure 6-24: InstallShield Wizard Welcome Screen Step 6: Click Next to continue the installation. Step 7:

PCIE-Q870-i2 PICMG 1.3 CPU Card Page xvTable 3-28: USB 3.0 Connector Pinouts...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 133 Figure 6-26: Restart the Computer Step 9: The confirmation screen offers the option of restarting the comp

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 134 Step 4: When the setup files are completely extracted the Welcome Screen in Figure 6-27 appears. Step 5

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 135 Figure 6-28: Intel® ME Driver License Agreement Step 9: Setup Operations are performed as shown in Figure

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 136 Figure 6-30: Intel® ME Driver Installation Finish Screen

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 137Appendix A A BIOS Options

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 138 Below is a list of BIOS configuration options in the BIOS chapter. 　 System Overview ...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 139　 Fan slope PWM ...

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 140 　 Save as User Defaults ...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 141 Appendix B B One Key Recovery

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 142 B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost

PCIE-Q870-i2 PICMG 1.3 CPU CardPage xvi BIOS Menus BIOS Menu 1: Main ...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 143After completing the five initial setup procedures as described above, users can access the recovery tool by

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 144 partitions. Please take the following table as a reference when calculating the size of the partition. OS

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 145 Linux o Fedora Core 12 (Constantine) o Fedora Core 11 (Leonidas) o Fedora Core 10 (Cambridge) o Fedora

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 146 The detailed descriptions are described in the following sections. NOTE: The setup procedures described b

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 147Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It wil

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 148 Figure B-4: Command Mode Step 5: The command prompt window appears. Type the following commands (marked in

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 149 Figure B-5: Partition Creation Commands

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 150 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 151B.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the syste

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 152 Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition.

PCIE-Q870-i2 PICMG 1.3 CPU Card Page xviiBIOS Menu 31: IEI Feature...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 153B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the sy

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 154 Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (71Figure

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 155Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as sho

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 156 Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in 71Figure B-17 prompts, c

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 157Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Imag

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 158 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step 0

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 159Step 1: Follow the steps described in Section B.2.1 ~ Section B.2.3 to setup BIOS, create partitions and in

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 160 Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD.

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 161 Figure B-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 162 Step 8: The Symantec Ghost starts to create the factory default image (Figure B-28). Figure B-28: Image Cr

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 1Chapter 1 1 Introduction

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 163BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 164  Partition 1: /  Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 165recovery partition. After completing the system configuration, press any key to reboot the system. Eject the

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 166 Step 7: The recovery tool menu appears. (71Figure B-33) Figure B-33: Recovery Tool Menu Step 8: Create a

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 167Figure B-34: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore:

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 168 B.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 169B.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press &

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 170 B.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Ty

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 171B.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and p

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 172 B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatic

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 2 1.1 Introduction Figure 1-1: PCIE-Q870-i2 The PCIE-Q870-i2 is a PICMG 1.3 CPU card. It accepts a Socket LGA11

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 173B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 174 filename “pxelinux.0”; Step 0: B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 175Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 176 B.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd resta

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 177Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes p

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 178 Figure B-42: Disable Automatically Restart Step 2: Configure the following BIOS options of the client sys

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 179 Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a ha

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 180 NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a fire

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 181 Step 5: When the following window appears, press <S> to select “Specify Additional Device”.

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 182 Step 6: In the following window, select a SATA controller mode used in the system. Then press <Enter>

PCIE-Q870-i2 PICMG 1.3 CPU CardPage ii Revision Date Version Changes 24 April, 2014 1.02 Modified LAN pinouts Updated Chapter 2: Packing List 24 M

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 31.2 Features Some of the PCIE-Q870-i2 motherboard features are listed below:  PICMG 1.3 full-size solution 

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 183Appendix C C Terminology

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 184 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configur

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 185DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 186 LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 187Appendix D D Digital I/O Interface

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 188 D.1 Introduction The DIO connector on the PCIE-Q870-i2 is interfaced to GPIO ports on the Super I/O chipset.

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 189MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call D.3.2 Enable the DIO Ou

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 190 Appendix E E Watchdog Timer

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 191 NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 192 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EX

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 4 1.3 Connectors The connectors on the PCIE-Q870-i2 are shown in the figure below. Figure 1-2: Connectors

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 193Appendix F F Intel® Matrix Storage Manager

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 194 F.1 Introduction The PCIE-Q870-i2 can provide data protection for serial ATA (SATA) disks via the Intel® Mat

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 195 CAUTION! Do not accidentally disconnect the SATA drive cables. Carefully route the cables within the chassi

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 196 appear during the POST. Refer to the applicable BIOS configuration section in this user manual. Step 4: Sav

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 197Appendix G G Hazardous Materials Disclosure

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 198 G.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Witho

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 199Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 200 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 51.4 Dimensions The main dimensions of the PCIE-Q870-i2 are shown in the diagram below. Figure 1-3: PCIE-Q870-

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 6 1.5 Data Flow 8Figure 1-4 shows the data flow between the system chipset, the CPU and other components install

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 71.6 Technical Specifications The PCIE-Q870-i2 technical specifications are listed below. Specification/Model

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 8 Specification/Model PCIE-Q870-i2 Display Output One VGA (up to 1920 x 1200, 60 Hz) One iDP interface for HDMI

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 9Specification/Model PCIE-Q870-i2 Operating Temperature -20ºC ~ 60ºC Storage Temperature -30ºC ~ 70ºC Humidity

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 10 Chapter 2 2 Packing List

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 112.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 12 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed wi

PCIE-Q870-i2 PICMG 1.3 CPU Card Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in ord

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 13Quantity Item and Part Number Image 1 Utility CD 1 Quick Installation Guide Table 2-1: Packing List 2.4

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 14 Item and Part Number Image 7.1-channel HD audio kit with Realtek ALC892 audio codec supporting dual audio st

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 15Item and Part Number Image LGA1150 cooler kit (1U chassis compatible, 65W) (P/N: CF-1150SC-R10) LGA1150 coo

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 16 Chapter 3 3 Connectors

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 173.1 Peripheral Interface Connectors This chapter details all the peripheral interface connectors. 3.1.1 PCIE-

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 18 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 19Connector Type Label Serial port, RS-232 10-pin box header COM1, COM3, COM4, COM5 Serial port, RS-422/485

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 20 3.2 Internal Peripheral Connectors The section describes all of the connectors on the PCIE-Q870-i2. 3.2.1 +12

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 21 Figure 3-3: Audio Connector Location Pin Description Pin Description 1 HDA_SYNC 2 HDA_BIT_CLK 3 HDA_SDOUT 4

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 22 Figure 3-4: Battery Connector Location Pin Description 1 VBATT 2 GND Table 3-5: Battery Connector (BAT1) Pi

PCIE-Q870-i2 PICMG 1.3 CPU CardPage iv Table of Contents 1 INTRODUCTION...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 233.2.5 DDR3 DIMM Slots CN Label: CHA_DIMM1, CHA_DIMM2, CHB_DIMM1, CHB_DIMM2 CN Type: DDR3 DIMM slot CN Locati

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 24 Pin Description Pin Description 1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 25Pin Description Pin Description 15 EC_EPP_PD6 16 EC_EPP_KSI5 17 EC_EPP_PD7 18 EC_EPP_KSI4 Table 3-8: EC De

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 26 3.2.9 Fan Connector (System) CN Label: SYS_FAN1 CN Type: 3-pin wafer CN Location: See Figure 3-10 CN Pinouts

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 27 Figure 3-11: Front Panel Connector Location Function Pin Description Function Pin Description 1 +5V

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 28 Figure 3-12: Internal DisplayPort Connector Location Pin Description Pin Description 1 +5V 11 AUXP 2 LANE

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 29 Figure 3-13: Infrared Connector Location Pin Description 1 +5V 2 NC 3 IRRX 4 GND 5 IRTX Table 3-13: Infrared

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 30 WARNING: The iRIS module slot is designed to install the iRIS-2400 module only. DO NOT install other modules

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 313.2.15 LAN LED Connectors CN Label: LED_LAN1, LED_LAN2 CN Type: 2-pin header CN Location: See 8Figure 3-16 C

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 32 The parallel port connector connects to a parallel port connector interface or some other parallel port devic

PCIE-Q870-i2 PICMG 1.3 CPU Card Page v3.2.12 Infrared Interface Connector... 2

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 333.2.17 PCIe Mini Card Slot CN Label: CN4 CN Type: PCIe Mini card slot CN Location: See 8Figure 3-18 CN Pinou

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 34 Pin Description Pin Description 35 GND 36 USB_DATA- 37 GND 38 USB_DATA+ 39 +3.3V 40 GND 41 +3.3V 42 N/C 43 +

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 35Pin Description 1 GND 2 SATA_TX+ 3 SATA_TX- 4 GND 5 SATA_RX- 6 SATA RX+ 7 GND Table 3-19: SATA 6Gb/s Drive Co

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 36 Pin Description Pin Description 1 DCD 2 DSR 3 RXD 4 RST 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 GND

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 37RS-422 Pinouts RS-485 Pinouts Table 3-22: DB-9 RS-422/485 Pinouts 3.2.21 SMBus Connector CN Label: CN2 CN

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 38 3.2.22 SPI Flash Connector CN Label: JSPI1 CN Type: 8-pin header CN Location: See Figure 3-23 CN Pinouts: Se

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 39 Figure 3-24: SPI EC Flash Connector Location Pin Description Pin Description 1 +3.3V 2 SPI_CS# 3 SPI

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 40 Pin Description Pin Description 1 LCLK 2 GND 3 LFRAME# 4 KEY 5 LRERST# 6 +5V 7 LAD3 8 LAD2 9

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 41Pin Description Pin Description 5 USB_DATA+ 6 USB_DATA- 7 GND 8 VCC Table 3-27: USB 2.0 Connector Pi

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 42 3.3 External Peripheral Interface Connector Panel The figure below shows the external peripheral interface co

PCIE-Q870-i2 PICMG 1.3 CPU CardPage vi 4.4.2 CPU Card Installation...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 43LED Description LED Description A on: linked blinking: data is being sent/received B off: 10 Mb/s green: 10

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 44 The VGA connector connects to a monitor that accepts a standard VGA input. Pin Description Pin Description

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 45Chapter 4 4 Installation

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 46 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the PCIE-Q87

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 47 WARNING: The installation instructions described in this manual should be carefully followed in order to pre

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 48 4.2.1 Socket LGA1150 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 49 Figure 4-2: Remove Protective Cover Step 3: Inspect the CPU socket. Make sure there are no bent pins and ma

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 50 Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 51Step 9: Connect the 12 V power to the board. Connect the 12 V power from the power supply to the board. Ste

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 52 Figure 4-5: Cooling Kit Support Bracket Step 2: Place the cooling kit onto the socket LGA1150 CPU. Make sur

PCIE-Q870-i2 PICMG 1.3 CPU Card Page vii5.3.9.2 Parallel Port Configuration ...

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 534.2.3 DIMM Installation To install a DIMM, please follow the steps below and refer to Figure 4-6. Figure 4-6

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 54 4.3 System Configuration The system configuration should be performed before installation. 4.3.1 AT/ATX Pow

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 554.3.3 Flash Descriptor Security Override The Flash Descriptor Security Override jumper specifies whether to o

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 56 4.3.5 PCIe x16 Interface Setup The PCIE-Q870-i2 supports one PCIe x16 interface on the backplane. The PCIe x1

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 574.4 Chassis Installation 4.4.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onbo

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 58 Step 2: Insert the cable connectors. Insert one connector into each serial port box headers (Figure 4-11). A

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 59 Figure 4-12: iRIS Module Installation Step 1: Locate the iRIS module slot. Place the PCIE-Q870-i2 on an a

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 60 Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA drive connector until

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 61Figure 4-14: SATA Power Drive Connection 4.5.4 USB Cable (Dual Port) with Slot Bracket The PCIE-Q870-i2 is sh

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 62 Step 3: Insert the cable connectors. Once the cable connectors are properly aligned with the USB connectors

PCIE-Q870-i2 PICMG 1.3 CPU CardPage viii B.2.3 Install Operating System, Drivers and Applications... 150 B.2.4 Bui

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 63 Figure 4-16: Remove the Retention Screws for the PCIe Mini Card Step 3: Insert into the socket at an angle.

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 64 Figure 4-18: Secure the PCIe Mini Card 4.6 External Peripheral Interface Connection This section describes c

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 65 Figure 4-19: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the L

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 66 Figure 4-20: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 67 Figure 4-21: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monito

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 68 process. Enter the Intel® current ME password as it requires (the Intel® default password is admin). Step 0:

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 69obtain IP address, follow the steps below: a. Copy the Ipmitool.exe file to a bootable USB flash drive. b. In

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 70 Figure 4-23: IEI iMAN Web GUI NOTE: To understand how to use the IEI iMAN Web GUI, please refer to the iRI

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 71Chapter 5 5 BIOS

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 72 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain

PCIE-Q870-i2 PICMG 1.3 CPU Card Page ixF.4 INSTALLING THE OPERATING SYSTEM TO THE RAID ARRAY ... 196 G HAZARDOUS MATE

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 73Key Function - Decrease the numeric value or make changes Page Up Move to the previous page Page Dn M

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 74  Security – Sets User and Supervisor Passwords.  Save & Exit – Selects exit options and loads default

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 755.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 76 Î System Overview The system overview lists a brief summary of the BIOS. The fields in system overview canno

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 77Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Sa

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 78 Î ACPI Sleep State [S1 only (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 79Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Wake system with F

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 80 5.3.3 Trusted Computing Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the Tru

PCIE-Q870-i2 PICMG 1.3 CPU Card Page 81Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced CPU Configuration

PCIE-Q870-i2 PICMG 1.3 CPU CardPage 82 Î Disabled DEFAULT Disables Intel Virtualization Technology. Î Enabled Enables Intel Virtualization Technolo