Iei-integration PM-1028 Bedienungsanleitung

1PM-1028-R20 PC/104 4/8-Port RS-232 Module PCB Ver2.0 Manual Revision 2.0 Jan, 24, 2006 @Copyright 2006 by ICP Electronics Inc. All Rights Reserv

10318-31FH OFF ON ON ON OFF OFF 320-327H OFF ON ON OFF ON ON 328-32FH OFF ON ON OFF ON OFF 330-337H OFF ON ON OFF OFF ON 338-33FH OFF ON ON OFF OFF O

11 COM Port I/O address COM Port I/O address COM1 Base Address + 00H COM2 Base Address + 08H COM3 Base Address + 10H COM4 Base Address + 18H

12*: Default

133 Connection This chapter describes how to connect peripherals, switches and indicators to the PM-1028 board. 3.1 RS-232 Connector The serial port

14 • CN2: COM5 ~ COM8 serial port connectors. PIN NO DESCRIPTION PIN NO DESCRIPTION1 DCD (COM8) 2 DSR (COM8) 3 RXD (COM8) 4 RTS (COM

153.2 PC/104 Expansion Bus The PC/104 expansion bus on the PM-1028enables you to attach the PM-1028 to the PC/104 slot on the target system.

16 •PC/104-64 Connector PIN NO DESCRIPTION PIN NO DESCRIPTION1 IOCHCK# 33 GND 2 SD7 34 IRSTDRV 3 SD6 35 VCC 4 SD5 36 IRQ9 5 SD4 37 -5V 6

17 4 Device Driver Installation 4.1 PM-1028 Device Driver Installation NOTE: It is necessary to go into the BIOS setup and ensure that the

18 Click “Next>” and the installation wizard starts to copy files to you hard disk. After the files are copied, PMSETUP.EXE is auto launched to t

19 Click “Finish” to complete the device driver installation.

2Contents 1. Introduction ... 3 1.1 Specifications ...

204.2 PM-1028 resource setup At device driver installation, the installation wizard copied a utility PMSETUP.EXE to your local hard disk and created

21Click “8 Ports” for PM-1028-8 or “4 Ports” for PM-1028-4. Select the “COM Port Base Address” and “ Interrupt Status Address” options that match the

22Check “Share one IRQ” if you want to share one IRQ for all ports, otherwise uncheck it and select different IRQ for each port. After you complete

23After the computer restarts, you can use Device Manager to check if all the PM-1028 ports were successfully added. For Windows XP: Go to Start -

24 For Windows NT: Go to Start -> Settings -> Control Panel -> Ports NOTE: To change jumper settings after ports are installed and liste

254.3 Uninstall PM-1028 Device Driver To uninstall PM-1028 device driver, go to start -> Settings -> Control Panel -> Add/Remove Programs.

26

31 Introduction The PM-1028 is a PC/104-compliant 4-port or 8-port RS-232 module with one TI 16C544Ahigh performance serial I/O chip integrated o

41.2 PM-1028 package contents PM-1028 package includes the following items: • 1 x User Manual • 1 x PM-1028 x 1 • 2 x Serial port cables ( 40 pin, 4

52 Installation This chapter describes how to install the PM-1028. 2.1 Hardware Installation Installation of the PC/104 modules on CPU card is quic

62.2 Board Layout

7Board Dimension (mm)

82.3 Interrupt Status address setting • JP9: Interrupt status address setting Interrupt Status Address 9-10 7-8 5-6 3-4 1-2200H ON ON ON ON ON210H O

92.4 COM Port I/O base address setting • JP10: COM Port I/O base address setting Base Address 11-12 9-10 7-8 5-6 3-4 1-2 *200-207H ON ON ON ON ON